eCRATER.com Forum Index

SearchSearch
ProfileProfile
  Log in to check your private messagesLog in to check your private messages   
Log inLog in

Sell Burglar Alarm, Fire Alarm, Environment Security Sensor

 
Post new topic   Reply to topic    eCRATER.com Forum Index -> Promote Your eCRATER Store
View previous topic :: View next topic  
Author Message
vedardalarms



Posts: 5

PostPosted: Sun Sep 25, 2016 3:07 am    Post subject: Sell Burglar Alarm, Fire Alarm, Environment Security Sensor Reply with quote

Sell Home Security Systems Burglar Alarm, Fire Alarm, Environment security sensors. There are Alarm Control Panel, Intrusion Detectors, Smoke Detector, Fire Alarm Control Panel, CO detector, Door and window contact, Perimeter Security Equipment.
At Ecrater Store http://vedardalarms.ecrater.com/
Back to top
View seller's profile Send private message Visit seller's eCRATER store
vedardalarms



Posts: 5

PostPosted: Mon May 06, 2019 6:25 pm    Post subject: Need help install home security system? Reply with quote

How to DIY home security? Where should I install the motion sensor? How to set the security monitor app? Can I install the solar wireless beam system by myself?
Get answer at vedardalarm FAQ of install alarm system.
For example:
How to install PIR and Door Contact for home security
Infrared detector is popular motion sensor. The PIR is used for security protection of bed rooms, living room, balcony etc. It is installed with bracket for angle adjustment. The detection area may be horizontal 110 degree, thickness 65 degree of fan-shaped area. Can you install the PIR according to the instruction manual? Below we will make clearer steps for guidance. Step1. Using impact drill to make two holes on the wall according to PIR bracket fixing hole. Then fix PIR bracket with screws (included in the PIR package) If there is no impact drill, using cement nail to fix the bracket on the wall. Step2. Insert the PIR body to the universal bracket. The PIR level angle and vertical angle can be adjusted for best detection. It is better to install PIR in the corner of wall to get best protection area. Select installation location, installation height according to PIR instruction manual. Below is the illustration of installation ways and effect. magnetic contact is another essential component of home security. Door contact includes two parts: magnetic switch and emitter. When these two parts are separated by about 1cm, the emitter will send alarm signal to siren strobe or alarm control panel. Magnetic contact can be used for alarm of door windows, fence or other protected objects. The emitter should be installed on fixed object such as the door frame. The magnetic switch should be installed on moving object such as door. If the door and the door frame is not at the same plane, you can use a small piece of wood to block up the low side. There are metal door contact, wood door contact and rolling door contact. Please select corresponding door contact for the door security protection. You can use double faced adhesive tape to fix the door contact or use screw to fix the door contact. It is better to use screw fix it. The alarm system installing manual will guide how to enroll the PIR, door contact to the alarm control panel. You should read the manual carefully and follow it.
Read More security alarm installation guide.
Back to top
View seller's profile Send private message Visit seller's eCRATER store
vedardalarms



Posts: 5

PostPosted: Mon May 06, 2019 6:30 pm    Post subject: What is beam system and how does it work Reply with quote

Beam system is active infrared detector. It is consist of transmitter terminal, receive terminal, Optical lens, LED indicator for light intensity etc.
The system works as invisible light wall. When someone is entering into the light wall, it blocked the beams. Then the detector triggers alarm for warning and notice. The beam system keeps working 24 hours.
To avoid false alarm of blocking by falling leaves, flying bird or small animals, the blocking time should be set not too short. But to ensure no missing alarm of quick passing theft, the blocking time should be set not too long. So, the blocking time or named sensitivity should be set accurately according to the environment. Factories may make the sensitivity adjustable at set value.
Below is the sensitivity adjustment way for Solar powered beams system.
HB-T001Q3+ is updated item of HB-T001Q3. It has new features of including LCD calibrator and trigger sensitivity adjusting. With built-in LCD calibrator, the transmitter terminal and receiver terminal can be easy calibrated for working.
Moreover, HB-T001Q3+ trigger sensitivity can be adjusted by customer.
Below is the steps to adjust the trigger sensitivity of HB-T001Q3+. How to program the sensitivity of the solar beams.
Sensitivity of the solar beams divided into 2 types: 200ms(factory default) and 100ms
Please follow up the operation steps if you want to switch the sensitivity of the beams to be 100ms
Step 1: Turn on the solar beams by press the ON/OFF button 3 times (both the transmitter and receiver)
Step 2: Long time press the ON/OFF button for 10 seconds and release the button when you hear bleep prompt (both the transmitter and receiver)
Step 3: Press the ON/OFF button 6 times (both the transmitter and receiver)
Step 4: Make sure the solar beams aligned with each other
Step 5: Long time press the ON/OFF button for 10 seconds and release the button when you hear bleep prompt (only the receiver) Step 6: Press the ON/OFF button 4 times (only the receiver)
Step 7: Program successfully when you hear bleep prompt
There are three types beams system. They are infrared beams, infrared grating, and infrared light wall.
They are applied at different situation. Infrared beam is installed on wall or fence. It has 3 Infrared light wall beams or 4 beam, 6 beams and length is short compared with other two types. So, it should be installed over the wall or fence or with bracket and pole to get enough protection height. But it has maximum 100 meters detection length. Infrared grating is used for windows, balcony or gate. It has 4 beams or 8 beams and with 620 mm to 1200 mm. The detection distance is 10 meters only.
Infrared light wall is used for fixing on ground and can have lamp on cover.
Back to top
View seller's profile Send private message Visit seller's eCRATER store
vedardalarms



Posts: 5

PostPosted: Mon May 06, 2019 6:35 pm    Post subject: Install Infrared Beams Detector Reply with quote

Installing active infrared beams detector is harder than installing passive infrared detector.
The beams detector is installed at outdoor open space. It is always fixed on pillar or on wall. We should firstly confirm the protection line and draw the installing place on drawing. Then we mark the accurate installing point on fixing object such as wall or pillar by level instrument or other tools.
Installing ways:
1. Installing the beams on pillar: there are some types of pillars such as pipe and square columns. The shapes are “1” shape, “z” shape or “L” shape. We should choose the correct type of pillar according to installing building feature and security protection requirement.
The pillar should be fixed on ground or other objects strongly and without moving or shaking. It is important to ensure the beams detector installing and working properly.
2. Installing the beams on wall: the infrared beams can be installed on wall or fence, windows directly. The Optical lens of the detector has automatic up and down adjustment of 20 degree.
Use fixing bracket to install the infrared beams on surface of wall or frame of windows.
Principles of installing infrared beams detectors: Detectors installed on passageway: It is used to stop illegal passing and avoid false alarm caused by pet or small animals. So, the beams should be installed more than 50 cm (from the infrared beams hole) over the ground. The beams blocking response speed should be set at fast rate.
Detectors installed on parapet wall: It is used to stop illegal climbing over the parapet wall. The beam can be installed over the top of the parapet wall or over the side of the parapet wall. It should be installed more than 25 cm (from the infrared beams hole) over the top of the parapet wall to avoid false alarm caused by bird or cat etc. animals. And the distance should be less than 30 cm between the beams hole and the wall inside part. When it is installed at side part of the parapet wall, it should be installed at outside part of the wall and near the top part. The installation way should be chosen according to protection requirement and building features. 4 beams infrared detector performed better than 3 beams to avoid false alarm.
Back to top
View seller's profile Send private message Visit seller's eCRATER store
vedardalarms



Posts: 5

PostPosted: Mon May 06, 2019 6:46 pm    Post subject: How to make home security solution Reply with quote

How to make home security solutions according to individual needs and budget?
Below we will give an example to explain it. The house is with 3 bed rooms, 2 bath rooms, 1 kitchen room, 1 study room and 2 balcony. Home security solution according to budget
The principle of making home security solution.
1.Plan and make external security firstly. In security alarm industry, it is perimeter security zones. The security protection areas are fence, wall, gate and house entrances including door, windows and balcony. The connection areas between the upper and lower floors, between house and neighbor’s house.
2.Then plan and make internal security. In security alarm industry, it is interior zones and fire zones. The security protection areas are aisle, hall, living room, kitchen room, bed room, bath room.
3.The alarm control panel installing principle:
A.Install it at place with telephone interface and hide it. Do not install it near the door or where theft can easy find and destroy it.
B.If the alarm control panel can not be installed at hidden place, then a PIR motion sensor should be installed to monitor the alarm control panel.
C.It is best to install the siren strobe outdoor and far from the alarm control panel.
D.If the siren strobe can not be installed outdoor, it is best to use wireless siren strobe and avoid theft finding the alarm control panel. Step 1: Define the protection range according to the house situation. From below drawing, we can know the most easy to be invaded place is two balconies, then is the out door. And kitchen room windows, study room windows cause these rooms are always vacant at night time and can be entrance of theft. Bath room, child room, main bed room are listed as protection areas with priority code. All protection areas are listed with priority code from 10 to 1 as below.
Step 2: Define defense zones and defense way, equipment for each zone. After protection areas and zone is defined, the defense equipment quantity and types should be defined according to the community security environment and family environment, behavior. The above home security solution design for example, we can use different equipment for different level defense. The equipment can be added or deducted according to budget and needs. Home intrusion places and alarm type 1.Simple type installation: With lowest budget and good security environment, we make simple type installation. Only gate No.7, balconies No.9 and No.10, kitchen room No.6, study room No.5 are defensed. Wireless door magnetism contact is used for gate No.7, kitchen room No.6 and study room No.5. PIR motion sensor is used for living room and bedroom to against intrusion from two balconies No.9 and No.10. The alarm system used is 1pc PIR motion sensor, 3 pcs door or windows open contact, one set alarm control panel with 1 PIR, 1 door contact, 2 keypad, remote controller. The functions of the simple type alarm system. A.When the gate or kitchen room window, study room window is opened, (door or window is leaving more than 1 cm from the door frame or window frame) or someone is entering into living room or bedroom from the balcony, the alarm system will go off and siren strobe makes sounder and lighting for warning. B.Backup battery is built-in and can work for 8-16 hours at AC off time. C.PIR motion sensor is used for zone 9 living room and home arm can be set when someone is at home. So, the living room PIR will not trigger alarm when someone is at home. D.If no one is at home, away home arm should be set and intrusion is detected at living room, the alarm goes off. The cons: When magnetic contact is used for windows security, the windows can not be opened even at summer time. basic home security installation solution 2.Basic type installation: Use wireless door windows magnetic switch for all doors and windows. Use 1 PIR motion sensor for addition of living room security protection. The functions of the basic type alarm system. A.When the gate or kitchen room window, study room window, bathroom window, child room window is opened, (door or window is leaving more than 1 cm from the door frame or window frame) or someone is entering into living room or bedroom from the balcony, the alarm system will go off and siren strobe makes sounder and lighting for warning. B. Backup battery is built-in and can work for 8-16 hours at AC off time. C. PIR motion sensor is used for zone 9 living room and home arm can be set when someone is at home. So, the living room PIR will not trigger alarm when someone is at home. D. If no one is at home, away home arm should be set and intrusion is detected at living room, the alarm goes off. Cons: When magnetic contact is used for windows security, the windows can not be opened even at summer time. When someone is at home, home arm should be set. improved home security solution 3.Practical type installation: Cause the basic type alarm system using windows contact for windows protection and the windows can not be opened at arm status, the curtain PIR is used to replace windows contact. The curtain PIR is with direction recognition and alarm goes off if theft entering from outdoor. The alarm will not go off if home owners is walking at home. Cons: The balcony security protection is not enough. The theft can enter into balcony without alarm going off. It alarms until theft goes into the house. plan home security solution with guide 4.High grade type installation: Use infrared fence as balcony and windows intrusion prevention security equipment. The infrared fence is installed outdoor and can stop intrusion outdoor. Smoke detectors and gas leakage sensors are used as well for fire prevention. Solar power wireless infrared fence can be used. It is easy to install and there is wireless to wired transceiver for connection with any third party alarm control panel. Smoke alarm and gas alarm should be set as 24 hours zone and not controlled by arm disarm setting. Home security solution with perimeter security 5.Complete type installation: With infrared fence installed outdoor for windows and door entrance prevention. And add outdoor PIR detector as well at balcony to ensure the alarm going off when the theft is at balcony. Add wireless siren strobe for warning and neighbor notice. So, home is more secured. Home security with fire prevention 6.Thorough security solution with smart home Smart home house appliance switch is added to complete type installation alarm system. The house appliance such as air conditioner, electric cooker, electric heater can be remote turned on or turned off by mobile phone, remote, smart home app or telephone calling.
Back to top
View seller's profile Send private message Visit seller's eCRATER store
Display posts from previous:   
Post new topic   Reply to topic    eCRATER.com Forum Index -> Promote Your eCRATER Store
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum